Poster of Linux kernelThe best gift for a Linux geek
SCP

SCP

Section: User Commands (1)
Local index Up

BSD mandoc
 

NAME

scp - secure copy (remote file copy program)  

SYNOPSIS

scp -words [-12346BCpqrv ] [-c cipher ] [-F ssh_config ] [-i identity_file ] [-l limit ] [-o ssh_option ] [-P port ] [-S program ] [[user @ ] host1 : file1 ] ... [[user @ ] host2 : file2 ]  

DESCRIPTION

scp copies files between hosts on a network. It uses ssh(1) for data transfer, and uses the same authentication and provides the same security as ssh(1). Unlike rcp(1), scp will ask for passwords or passphrases if they are needed for authentication.

File names may contain a user and host specification to indicate that the file is to be copied to/from that host. Local file names can be made explicit using absolute or relative pathnames to avoid scp treating file names containing `:' as host specifiers. Copies between two remote hosts are also permitted.

The options are as follows:

-1
Forces scp to use protocol 1.
-2
Forces scp to use protocol 2.
-3
Copies between two remote hosts are transferred through the local host. Without this option the data is copied directly between the two remote hosts. Note that this option disables the progress meter.
-4
Forces scp to use IPv4 addresses only.
-6
Forces scp to use IPv6 addresses only.
-B
Selects batch mode (prevents asking for passwords or passphrases).
-C
Compression enable. Passes the -C flag to ssh(1) to enable compression.
-c cipher
Selects the cipher to use for encrypting the data transfer. This option is directly passed to ssh(1).
-F ssh_config
Specifies an alternative per-user configuration file for ssh This option is directly passed to ssh(1).
-i identity_file
Selects the file from which the identity (private key) for public key authentication is read. This option is directly passed to ssh(1).
-l limit
Limits the used bandwidth, specified in Kbit/s.
-o ssh_option
Can be used to pass options to ssh in the format used in ssh_config5. This is useful for specifying options for which there is no separate scp command-line flag. For full details of the options listed below, and their possible values, see ssh_config5.

AddressFamily
BatchMode
BindAddress
ChallengeResponseAuthentication
CheckHostIP
Cipher
Ciphers
Compression
CompressionLevel
ConnectionAttempts
ConnectTimeout
ControlMaster
ControlPath
GlobalKnownHostsFile
GSSAPIAuthentication
GSSAPIDelegateCredentials
HashKnownHosts
Host
HostbasedAuthentication
HostKeyAlgorithms
HostKeyAlias
HostName
IdentityFile
IdentitiesOnly
IPQoS
KbdInteractiveDevices
KexAlgorithms
LogLevel
MACs
NoHostAuthenticationForLocalhost
NumberOfPasswordPrompts
PasswordAuthentication
PKCS11Provider
Port
PreferredAuthentications
Protocol
ProxyCommand
PubkeyAuthentication
RekeyLimit
RhostsRSAAuthentication
RSAAuthentication
SendEnv
ServerAliveInterval
ServerAliveCountMax
StrictHostKeyChecking
TCPKeepAlive
UsePrivilegedPort
User
UserKnownHostsFile
VerifyHostKeyDNS

-P port
Specifies the port to connect to on the remote host. Note that this option is written with a capital `P' because -p is already reserved for preserving the times and modes of the file in rcp(1).
-p
Preserves modification times, access times, and modes from the original file.
-q
Quiet mode: disables the progress meter as well as warning and diagnostic messages from ssh(1).
-r
Recursively copy entire directories. Note that scp follows symbolic links encountered in the tree traversal.
-S program
Name of program to use for the encrypted connection. The program must understand ssh(1) options.
-v
Verbose mode. Causes scp and ssh(1) to print debugging messages about their progress. This is helpful in debugging connection, authentication, and configuration problems.

 

EXIT STATUS

Ex -std scp  

SEE ALSO

rcp(1), sftp(1), ssh(1), ssh-add1, ssh-agent1, ssh-keygen1, ssh_config5, sshd(8)  

HISTORY

scp is based on the rcp(1) program in BSD source code from the Regents of the University of California.  

AUTHORS

An Timo Rinne Aq tri@iki.fi An Tatu Ylonen Aq ylo@cs.hut.fi


 

Index

NAME
SYNOPSIS
DESCRIPTION
EXIT STATUS
SEE ALSO
HISTORY
AUTHORS

This document was created by man2html, using the manual pages.
Time: 21:25:44 GMT, April 16, 2011