Poster of Linux kernelThe best gift for a Linux geek
FSDB

FSDB

Section: Maintenance Commands (8)
Local index Up

BSD mandoc
 

NAME

fsdb - FFS debugging/editing tool  

SYNOPSIS

[-d ] [-f ] [-r ] fsname  

DESCRIPTION

The utility opens fsname (usually a raw disk partition) and runs a command loop allowing manipulation of the file system's inode data. You are prompted to enter a command with fsdb (inum X)> where X is the currently selected i-number. The initial selected inode is the root of the file system (i-number 2). The command processor uses the editline(3) library, so you can use command line editing to reduce typing if desired. When you exit the command loop, the file system superblock is marked dirty and any buffered blocks are written to the file system.

The following options are available:

-d
Enable additional debugging output (which comes primarily from fsck(8)Ns-derived code).
-f
Left for historical reasons and has no meaning.
-r
Open the file system read/only, and disables all commands that would write to it.

 

COMMANDS

Besides the built-in editline(3) commands, supports these commands:

help
Print out the list of accepted commands.

inode i-number
Select inode i-number as the new current inode.

back
Revert to the previously current inode.

clri i-number
Clear i-number

lookup name
cd name
Find name in the current directory and make its inode the current inode. Name may be a multi-component name or may begin with slash to indicate that the root inode should be used to start the lookup. If some component along the pathname is not found, the last valid directory encountered is left as the active inode. This command is valid only if the starting inode is a directory.

active
print
Print out the active inode.

blocks
Print out the block list of the active inode. Note that the printout can become long for large files, since all indirect block pointers will also be printed.

findblk disk_block_number ...
Find the inode(s) owning the specified disk block(s) number(s). Note that these are not absolute disk blocks numbers, but offsets from the start of the partition.

uplink
Increment the active inode's link count.

downlink
Decrement the active inode's link count.

linkcount number
Set the active inode's link count to number

ls
List the current inode's directory entries. This command is valid only if the current inode is a directory.

rm name
del name
Remove the entry name from the current directory inode. This command is valid only if the current inode is a directory.

ln ino name
Create a link to inode ino under the name name in the current directory inode. This command is valid only if the current inode is a directory.

chinum dirslot inum
Change the i-number in directory entry dirslot to inum

chname dirslot name
Change the name in directory entry dirslot to name This command cannot expand a directory entry. You can only rename an entry if the name will fit into the existing directory slot.

chtype type
Change the type of the current inode to type Type may be one of: file dir socket or fifo

chmod mode
Change the mode bits of the current inode to mode You cannot change the file type with this subcommand; use chtype to do that.

chflags flags
Change the file flags of the current inode to flags

chown uid
Change the owner of the current inode to uid

chgrp gid
Change the group of the current inode to gid

chgen gen
Change the generation number of the current inode to gen

btime time
mtime time
ctime time
atime time
Change the creation (birth), modification, change, or access time (respectively) on the current inode to time Time should be in the format YYYYMMDDHHMMSS[.nsec] where nsec is an optional nanosecond specification. If no nanoseconds are specified, the birthnsec mtimensec ctimensec or atimensec field will be set to zero. Note that btime is available on UFS2 file systems only.

quit , q , exit , <EOF>
Exit the program.

 

SEE ALSO

editline(3), fs(5), clri(8), fsck(8)  

HISTORY

The utility uses the source code for fsck(8) to implement most of the file system manipulation code. The remainder of first appeared in Nx , written by An John T. Kohl .

An Peter Wemm ported it to Fx .  

BUGS

Manipulation of ``short'' symlinks has no effect. In particular, one should not try changing a symlink's type.

You must specify modes as numbers rather than symbolic names.

There are a bunch of other things that you might want to do which does not implement.  

WARNING

Use this tool with extreme caution--you can damage an FFS file system beyond what fsck(8) can repair.


 

Index

NAME
SYNOPSIS
DESCRIPTION
COMMANDS
SEE ALSO
HISTORY
BUGS
WARNING

This document was created by man2html, using the manual pages.
Time: 22:01:39 GMT, April 16, 2011