snmpd - daemon to respond to SNMP request packets.
[OPTIONS] [LISTENING ADDRESSES]
is an SNMP agent which binds to a port and awaits requests from
SNMP management software. Upon receiving a request, it processes the
request(s), collects the requested information and/or performs the
requested operation(s) and returns the information to the sender.
Log the source addresses of incoming requests.
Append to the log file rather than truncating it.
as a configuration file
(or a comma-separated list of configuration files). Note that the loaded
file will only understand snmpd.conf tokens, unless the configuration type
is specified in the file as described in the snmp_config man page under
SWITCHING CONFIGURATION TYPES IN MID-FILE.
Do not read any configuration files except the ones optionally specified by the
Note that this behaviour also covers the persistent configuration files.
This may result in dynamically-assigned values being reset following an
agent restart, unless the relevant persistent config files are
explicitly loaded using the
Dump (in hexadecimal) the sent and received SNMP packets.
Turn on debugging output for the given
Without any tokens specified, it defaults to printing all the tokens
(which is equivalent to the keyword "ALL").
You might want to try
for extremely verbose output. Note: You can not put a space between
the -D flag and the listed TOKENs.
Do not fork() from the calling shell.
Change to the numerical group ID
after opening listening sockets.
Display a brief usage message and then exit.
Display a list of configuration file directives understood by the
agent and then exit.
Specifies which modules should (or should not) be initialized
when the agent starts up. If the comma-separated
with a '-', it is the list of modules that should not be started.
Otherwise this is the list of the only modules that should be started.
To get a list of compiled modules, run the agent with the arguments
(assuming debugging support has been compiled in).
Specify where logging output should be directed (standard error or output,
to a file or via syslog). See LOGGING OPTIONS in snmpcmd(5) for details.
Specifies a colon separated list of MIB modules to load for this
application. This overrides the environment variable MIBS.
See snmpcmd(1) for details.
Specifies a colon separated list of directories to search for MIBs.
This overrides the environment variable MIBDIRS.
See snmpcmd(1) for details.
Set an alternative application name (which will affect the
configuration files loaded).
By default this will be snmpd, regardless of the name
of the actual binary.
Save the process ID of the daemon in
Print simpler output for easier automated parsing.
Do not require root access to run the daemon. Specifically, do not exit
if files only accessible to root (such as /dev/kmem etc.) cannot be
Change to the user ID
(which can be given in numerical or textual form) after opening
Instructs the agent to not remove its pid file (see the
option) on shutdown. Overrides the leave_pidfile token in the
Print version information for the agent and then exit.
Symbolically dump SNMP transactions.
Listens for AgentX connections on the specified address
rather than the default "/var/agentx/master".
The address can either be a Unix domain socket path,
or the address of a network interface. The format is the same as the
format of listening addresses described below.
Run as an AgentX subagent rather than as an SNMP master agent.
Allows to specify any token ("name") supported in the
file and sets its value to "value". Overrides the corresponding token in the
for the full list of tokens.
listens for incoming SNMP requests on UDP port 161 on all IPv4 interfaces.
However, it is possible to modify this behaviour by specifying one or more
listening addresses as arguments to snmpd.
A listening address takes the form:
At its simplest, a listening address may consist only of a port
number, in which case
listens on that UDP port on all IPv4 interfaces. Otherwise, the
<transport-address> part of the specification is parsed according to
the following table:
aal5pvc or pvc
udp6 or udpv6 or udpipv6
tcp6 or tcpv6 or tcpipv6
Note that <transport-specifier> strings are case-insensitive so that,
for example, "tcp" and "TCP" are equivalent. Here are some examples,
along with their interpretation:
listen on UDP port 161, but only on the loopback interface. This
being queried remotely. The port specification ":161" is
not strictly necessary since that is the default SNMP port.
listen on TCP port 1161 on all IPv4 interfaces.
listen on IPX port 40000 on all IPX interfaces.
listen on the Unix domain socket /tmp/local-agent.
is identical to the previous specification, since the Unix domain is
assumed if the first character of the <transport-address> is '/'.
listen on the AAL5 permanent virtual circuit with VPI=0 and VCI=161
(decimal) on the first ATM adapter in the machine.
listen on port 10161 on all IPv6 interfaces.
Note that not all the transport domains listed above will always be
available; for instance, hosts with no IPv6 support will not be able
to use udp6 transport addresses, and attempts to do so will result in
the error "Error opening specified endpoint". Likewise, since AAL5
PVC support is only currently available on Linux, it will fail with
the same error on other platforms.
checks for the existence of and parses the following files:
Common configuration for the agent and applications. See
Agent-specific configuration. See
for details. These files are optional and may be used to configure
access control, trap generation, subagent protocols and much else
In addition to these two configuration files in /etc/snmp, the
agent will read any files with the names
in a colon separated path specified in the
SNMPCONFPATH environment variable.
The agent will also load all files in this directory as MIBs. It will
not, however, load any file that begins with a '.' or descend into