The framework provides boot time initialization, rules files for adding custom rules, a method for loading netfilter modules, configuration of kernel parameters and configuration of IPv6. The framework consists of the following files:
ufw is started on boot with /lib/ufw/ufw-init. This script is a standard SysV style initscript used by the ufw command and should not be modified. It supports the following arguments:
ufw uses many user-defined chains in addition to the built-in iptables chains. If MANAGE_BUILTINS in /etc/default/ufw is set to 'yes', on stop and reload the built-in chains are flushed. If it is set to 'no', on stop and reload the ufw secondary chains are removed and the ufw primary chains are flushed. In addition to flushing the ufw specific chains, it keeps the primary chains in the same order with respect to any other user-defined chains that may have been added. This allows for ufw to interoperate with other software that may manage their own firewall rules.
To ensure your firewall is loading on boot, you must integrate this script into the boot process. Consult your distribution's documentation for the proper way to modify your boot process if ufw is not already integrated.
ufw is in part a front-end for iptables-restore, with its rules saved in /etc/ufw/before.rules, /etc/ufw/after.rules and /lib/ufw/user.rules. Administrators can customize before.rules and after.rules as desired using the standard iptables-restore syntax. Rules are evaluated as follows: before.rules first, user.rules next, and after.rules last. IPv6 rules are evaluated in the same way, with the rules files named before6.rules, user6.rules and after6.rules. Please note that ufw status only shows rules added with ufw and not the rules found in the /etc/ufw rules files.
Important: ufw only uses the *filter table by default. You may add any other tables such as *nat, *raw and *mangle as desired. For each table a corresponding COMMIT statement is required.
After modifying any of these files, you must reload ufw for the rules to take effect. See the EXAMPLES section for common uses of these rules files.
Netfilter has many different connection tracking modules. These modules are aware of the underlying protocol and allow the administrator to simplify his or her rule sets. You can adjust which netfilter modules to load by adjusting IPT_MODULES in /etc/default/ufw. Some popular modules to load are:
ufw will read in /etc/ufw/sysctl.conf on boot when enabled. Please note that /etc/ufw/sysctl.conf overrides values in the system systcl.conf (usually /etc/sysctl.conf). Administrators can change the file used by modifying /etc/default/ufw.
IPv6 is disabled by default and all incoming, outging and forwarded packets are dropped, with the exception of traffic on the loopback interface. To change this behavior, set IPV6 to 'yes' in /etc/default/ufw. See the ufw manual page for details.
As mentioned, ufw loads its rules files into the kernel by using the iptables-restore and ip6tables-restore commands. Users wanting to add rules to the ufw rules files manually must be familiar with these as well as the iptables and ip6tables commands. Below are some common examples of using the ufw rules files. All examples assume IPv4 only and that DEFAULT_FORWARD_POLICY in /etc/default/ufw is set to DROP.
To allow IP masquerading for computers from the 10.0.0.0/8 network to share the single IP address on eth0:
To forward tcp port 80 on eth0 to go to the webserver at 10.0.0.2:
To block RFC1918 addresses going out of eth0:
This example combines the other examples and demonstrates a simple routing firewall. Warning: this setup is only an example to demonstrate the functionality of the ufw framework in a concise and simple manner and should not be used in production without understanding what each part does and does not do. Your firewall will undoubtedly want to be less open.
This router/firewall has two interfaces: eth0 (Internet facing) and eth1 (internal LAN). Internal clients have addresses on the 10.0.0.0/8 network and should be able to connect to anywhere on the Internet. Connections to port 80 from the Internet should be forward to 10.0.0.2. Access to ssh port 22 from the administrative workstation (10.0.0.100) to this machine should be allowed. Also make sure no internal traffic goes to the Internet.
-A ufw-before-forward -i eth1 -s 10.0.0.0/8 -o eth0 -m state \
--state NEW -j ACCEPT
-A ufw-before-forward -m state --state NEW -i eth0 \
-d 10.0.0.2 -p tcp --dport 80 -j ACCEPT
-A ufw-before-forward -o eth0 -d 10.0.0.0/8 -j REJECT
-A ufw-before-forward -o eth0 -d 172.16.0.0/12 -j REJECT
-A ufw-before-forward -o eth0 -d 192.168.0.0/16 -j REJECT
ufw, iptables(8), ip6tables(8), iptables-restore(8), ip6tables-restore(8), sysctl(8), sysctl.conf(5)
ufw is Copyright 2008-2009, Canonical Ltd.
ufw and this manual page was originally written by Jamie Strandboge <firstname.lastname@example.org>